[Boards: 3 / a / aco / adv / an / asp / b / biz / c / cgl / ck / cm / co / d / diy / e / fa / fit / g / gd / gif / h / hc / his / hm / hr / i / ic / int / jp / k / lgbt / lit / m / mlp / mu / n / news / o / out / p / po / pol / qa / r / r9k / s / s4s / sci / soc / sp / t / tg / toy / trash / trv / tv / u / v / vg / vp / vr / w / wg / wsg / wsr / x / y ] [Home]
4chanarchives logo
I need help.
Images are sometimes not shown due to bandwidth/network limitations. Refreshing the page usually helps.

You are currently reading a thread in /diy/ - Do It yourself
Thread replies: 6
Thread images: 3
Anonymous
I need help. 2016-06-20 19:01:26 Post No. 1011582
[Report] Image search: [Google]
File: 51QI8tVo+GL.jpg (58 KB, 500x500) Image search: [Google]
51QI8tVo+GL.jpg
58 KB, 500x500
I need help. Anonymous 2016-06-20 19:01:26 Post No. 1011582 [Report]
anyone got a aurora 3d printer here? i need the pre configerated configs. i bought it from gearbest, and the drivers were crap. everything went backwards. i need a new copy but there is nowhere to download it. please post a link for me!
>>
Anonymous 2016-06-20 21:37:54 Post No.1011650
[Report]
Anonymous 2016-06-20 21:37:54 Post No.1011650 [Report]
You need to invert the axis anon. There should be check boxes for this in the settings. Read the instructions
>>
OP 2016-06-20 22:06:34 Post No.1011668
[Report]
OP 2016-06-20 22:06:34 Post No.1011668 [Report]
>>1011650
I need a fresh config to work with. i am using marlin right now. it seems close to what i need. i just neet to know what to do. there are no instructions though, because gearbest is chinamade KO crap.
>>
Anonymous 2016-06-20 22:10:10 Post No.1011671
[Report]
Anonymous 2016-06-20 22:10:10 Post No.1011671 [Report]
>>1011650
He probably installed the stepper wires backwards

>>1011668
Its just an i3, go through and build the settings yourself. Its not hard, you should know what you have
>>
Anonymous 2016-06-20 22:52:15 Post No.1011692
[Report] Image search: [Google]
Anonymous 2016-06-20 22:52:15 Post No.1011692 [Report]
File: blow yourself.jpg (47 KB, 634x297) Image search: [Google]
blow yourself.jpg
47 KB, 634x297
>everything went backwards.
>there are no instructions
>because gearbest

The problem is you.
>>
Anonymous 2016-06-20 22:54:24 Post No.1011694
[Report] Image search: [Google]
Anonymous 2016-06-20 22:54:24 Post No.1011694 [Report]
File: 1466222073000.jpg (279 KB, 972x1076) Image search: [Google]
1466222073000.jpg
279 KB, 972x1076
Learn 2 firmware, bro. There is no copy of marlin firmware that just works perfectly as soon as you push it to a printer. You will have to test and make changes one at time until it runs right.

If you are unwilling to do this, then be prepared to buy a 1000 dollar machine, and get off /diy/ because we are a community and not tech support.
Thread replies: 6
Thread images: 3
banner
banner
[Boards: 3 / a / aco / adv / an / asp / b / biz / c / cgl / ck / cm / co / d / diy / e / fa / fit / g / gd / gif / h / hc / his / hm / hr / i / ic / int / jp / k / lgbt / lit / m / mlp / mu / n / news / o / out / p / po / pol / qa / r / r9k / s / s4s / sci / soc / sp / t / tg / toy / trash / trv / tv / u / v / vg / vp / vr / w / wg / wsg / wsr / x / y] [Home]
All trademarks and copyrights on this page are owned by their respective parties. Images uploaded are the responsibility of the Poster. Comments are owned by the Poster.
If a post contains personal/copyrighted/illegal content you can contact me at [email protected] with that post and thread number and it will be removed as soon as possible.
DMCA Content Takedown via dmca.com
All images are hosted on imgur.com, send takedown notices to them.
This is a 4chan archive - all of the content originated from them. If you need IP information for a Poster - you need to contact them. This website shows only archived content.